Turn the gas valve counterclockwise until it reads 'pilot.' push the red 'reset' button and hold it down while you light the pilot burner with a match. Hot water heater thermostat thermostt gs electric reset button.
Clear 4 blink fault code on honeywell water heater gas valve high.
How to light a water heater with electronic pilot honeywell. Water heater pilot light issues: They have a gas control that searches for a status light that squints when the pilot is lit and a little igniter button, conceivably with a lightning bolt image close to it. Numerous recent water heaters necessitate that you realize how to light a water heater with the electronic pilot.
While holding the pilot button in depress the sparkler button a few times. This hot water heater will not light. Once there is a need for heating (or call from a thermostat), a gas control valve releases the gas into the main burner, and the pilot light ignites the gas.
Either a water heater is running or not. Turn the gas valve to the pilot setting and push down on it. When the pilot light goes out, here’s how to light a gas water heater pilot light:when the status (1 flash) with the knob in the pilot position.when this happens, the gas valve closes, extinguishes the pilot light and your water heater stops heating water.
Doing this starts the flow of gas into the tube that supplies the pilot light. Customer reply replied 6 years ago. A functioning pilot light should appear blue in color, which can help you determine whether or not your pilot light is working.
Wait five minutes for any gas remaining in the furnace to vent. If your water heater’s gas valve does not push down, look for a red control button near the valve. Honeywell hot water heater thermostat.
Disconnect control valve disconnecting the gas control valve is the first step in maintaining the electronic ignition or standby pilot water heaters: Using an electronic ignition heater, the pilot flame will light only when the thermostat requires the burner to be lit. I am able to get the pilot light to light and after a short delay, the indicator light on the control valve led status light begins to flash normally.
I have a state industries gs650ybrt 300 water heater with the honeywell electronic gas control valve. Make sure the gas control valve is turned to hot and wait for the water heater to heat back up. A pilot light is a small flame present to ignite the gas burner on your water heater.
Let’s start by explaining the water heater pilot light so you can better understand how it functions. One can still purchase a gas furnace or water heater with the old standing pilot ignition systems.these systems have been proven reliable and safe over time. I have a state industries gs650ybrt 300 water heater with the honeywell electronic gas control valve.
The air intake is located on the bottom or side of the water heater and may need to be cleaned out in order for the pilot to stay lit. Honeywell gas control valve troubleshooting for water heaters. L8104b with potentiometer remote potentiometer sensing bulb l8104a,b are used in standing pilot and electronic ignition systems.
A hot surface ignition system uses an electronically controlled resistance heating element, not unlike a light bulb filament, to ignite the gas burner. Read descriptions for imp info volume 1 introduction problem. Clear 4 blink fault code on honeywell water heater gas valve high.
You have to put your ear down to the floor to see the pilot. How to light the pilot light on a honeywell vr8200 set your thermostat to the lowest setting and unplug your furnace. Status light does not blink.
If the status light is flashing once every three seconds, the pilot light is lit and the gas control valve is working properly. If you don’t see a spark at all when you are trying to light your pilot it may be that you are not looking in at the right angle. If you have a very weak pilot that will only light with a grill lighter (not the piezo igniter)then a dirty orifice is the most likely culprit.
How to light a water heater honeywell electronic gas control youtube. Especially if you live in an area where there are frequent power outages. Lighting the pilot light for a standing pilot gas system is possible whereas lighting the pilot for an electronic ignition system.
I am able to get the pilot light to light and after a short delay, the indicator light on the control valve led status light begins to flash normally. This hot water heater will not light. A pilot light is always burning while using a small amount of gas;
The standing pilot water heater is better than an electronic ignition water heater. Poor gas pressure is another possibility but you'd need a gas pressure gauge (reads in inches of water column) or a manometer to check that. However the water heater kicks back on and gets back up to temperature and shuts off as normal and you will.i am able to get the pilot light to light and after a short delay, the indicator light on the control valve led status light begins to flash normally.i have a state industries gs650ybrt 300 water heater with the honeywell electronic gas.
Pilot light on water heater dhwanidhc com. 327306 000 state service handbook indd. It may take several hours for the water to heat up.