How To Light A Whirlpool Water Heater With Electronic Pilot

You should be able to see it above or next to the gas supply line for the pilot light. A water heater igniter has a sparking tip that is directed at the location of the pilot light.

Coleman Furnace Wiring Diagram Heat Sequencer Timings

The other tell tale sign is the wire that runs from the gas valve to the igniter.


How to light a whirlpool water heater with electronic pilot. A pilot light can go out. When lighting the pilot, make sure the knob on the gas control valve is set to pilot and if fully pushed in. If the status light is not flashing, try lighting the pilot using the instructions on the water heater's label.

If your gas water heater has an electronic ignition system, you should never attempt to light it by hand. In most cases, the water heater has gone out, and many people are trying to fix the furnace. A hot surface ignition system uses an electronically controlled resistance heating element, not unlike a light bulb filament, to ignite the gas burner.

Nowadays, modern water heaters use electronic ignition systems to light the pilot. Look at the status light on the gas control valve. Water heater pilot light issues:

There will be a red or black button marked “ignition,” press it for about 60 seconds. If the status light is flashing once every three seconds, the pilot light is lit and the gas control valve is working properly. But they may be confused and surprise when they find out that their furnace does not have a pilot light at all.

How do you know if the pilot light is out on a whirlpool water heater? When lighting the pilot, make sure the knob on the gas control valve is fully pushed in. This effectively shuts down the system, so you will get no heat from the appliance if the pilot is not working properly.

Either a water heater is running or not. The job of the pilot or igniter is to ignite the gas flowing from the main gas valve to the appliance burners. How to light a gas water heater pilot light.

Make sure the gas supply valve is turned on. So you are tired of relighting the pilot light every so often or replacing the thermocouple on your standing pilot gas water heater.you want to replace the standing pilot gas valve with an electronic ignition gas system so you can never have to ever worry about. How to light a water heater with electronic pilot:

How to light the pilot for a gas hot water heater. If your water heater’s gas valve does not push down, look for a red control button near the valve. A functioning pilot light should appear blue in color, which can help you determine whether or not your pilot light is working.

A pilot light is a small flame present to ignite the gas burner on your water heater. I don''t smell gas, but we don''t have hot water. The procedure for properly lighting a pilot light will vary based on the water heater you have.

It is common on fireplaces and older/cheaper furnaces and water heaters. A pilot light is always burning while using a small amount of gas; As this occurs, they produce a small voltage of electricity that passes over to the gas control valve.

Hold the pilot button down to “prime” the thermocouple—otherwise it will cut the gas supply to the pilot light. Doing this starts the flow of gas into the tube that supplies the pilot light. Let’s start by explaining the water heater pilot light so you can better understand how it functions.

I have a whirlpool gas water heater and the gas is turned. When it comes to your hot water heater, the pilot light heats up the thermopile. Release the reset button (s) slowly to make sure the pilot light stays lit, and then turn the control button to “on.”.

Turn the gas valve to the pilot setting and push down on it. A pilot light is a small device designed to provide the flame and light the gas coming out of the gas valve and main burner. When this happens, there is no electricity, so it shuts down the gas control valve until the light is relit.

All pilots have a safety system that prevents the main gas valve from staying open if the pilot flame has gone out or the igniter has failed. Lighting a water heater with an electronic pilot may be one of the many questions on the internet. Keep the knob pushed in while clicking the spark igniter button.

The most common issue that leads to repeated pilot outages is a dirty or bent thermocouple, which is a small copper wire and rod that senses the flame and automatically turns the. If the status light is flashing more than once every three seconds or not flashing at all, select the appropriate code below. Pilot lights, status light flashes.

You will hear the clicking sound of the igniter sparking. Keep the knob pushed in while repeatedly clicking the spark igniter button. Therefore, you should always consult the instructions from your manufacturer.

I have a whirlpool gas water heater and the gas is turned on but the pilot light is out, and it won''t light. Vocational, technical or trade scho.

Read More